Showing posts with label IS:456-1978. Show all posts
Showing posts with label IS:456-1978. Show all posts
RECOMMENDATIONS GIVEN IN THE CODE FOR PRACTICE IS :456-1978 BASED ON THE COMMENTARY PREPARED BY THE INDIAN STANDARD INSTITUTION .
To amplify the recommendations given in the code IS :456-1978 ,a commentary on the code is being prepared by the Indian Standard institution. To reduce the design time in the use of certain clauses in the code for design of beams,slabs and Columns in general building Structures SP:16-1979Design Aids for reinforced concrete to IS :456-1978 is being published.In addition , handbooks on concrete mix Design and the concrete reinforcement are being prepared.(2) The sectional Committee responsible for the preparation of this standard has taken into consideration the view points of manufacturers, users , Engineers, architects ,builders and technologists and has related the standard to the manufacturing and trade practices followed in the country in the field of experience and expertise opinion .Due weightage has also been given to the need for international coordination among Standard prevailing in the different countries of the world.(3) For the purpose of deciding whether a particular requirement of this standard is complied with, the final value,observed or calculated, expressing the result of a test or analysis , shall be rounded off in accordance with IS:2-1960 . The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard.(4) In the code it has been assumed that the Design of plain and the reinforced cement concrete work is entrusted to a qualified Engineer and that the execution of the cement concrete work is carried out under the direction of an experienced supervisor.
IS:456-1978 CODE FOR PRACTICE ADOPTED BY THE INDIAN STANDARD HAVE BEEN TIME TO TIME MODIFIED AND REVISED BY THE COUNCIL OF THE CIVIL ENGINEERING DEPARTMENT.
INDIAN STANDARD CODE OF PRACTICE FOR PLAIN AND REINFORCED CONCRETE.:-- IS :456-1978 the Indian standard was adopted by the Indian standard institution after the draft finalization of the cement and concrete and was according approved by the civil engineering council during 1978 .The standard was first published in 1953 under the title code of practice for plain and reinforced concrete for general building construction etc and subsequently revised in 1957 and was further revised during 1964 and published under the modified code thus enlarging the scope of use of this code along with number of changes and the addition. The present revision was taken up with a view to keeping abreast with the rapid development in the field of concrete technology and also to bring in further clarifications and the modifications in the light of experience gained while applying the provision of the earlier versions of the code to practical approach and situations arrived .The format and arrangements of clauses in the code for practice have been changed from the earlier version .The matter has now been divided into the six sections (1) General (2) Materials, workmanship, inspection and Testing (3) General Design requirements (4) Special design requirements for structural members and system adopted.(5) Structural design (Limit State method) (6) Structural design (Working stress Method) .An attempt has been made to unify the the approach for the design of reinforced concrete and prestressed concrete structures and the code of practice for prestressed concrete (IS :1343)is being revised simultaneously hence the section 2and 3 could be applicable to both the codes , except where modified in the prestressed concrete code .The recommendations of ISO 3898 -1976 have been taken into consideration
THEORY OF RCC DESIGN AND METHODS OF DESIGN ACCORDING TO THE IS:456-1978 (CODE FOR PRACTICE)
THEORY OF RCC AND DESIGN :--Two methods of design for RC structures are used ie the Working stress or elastic method and the load factor or ultimate load method. In the working stress method,the design is based on the working loads and the criterion for the strength of structure is its capacity to sustain the load and forces imposed on it .The load factor method of design is based on a determination of the load at which a structure fails and a certain factor of safety is adopted. The working stress method of design, which is the older and by for the still most commonly used by practicing Engineers .The factor of safety related with ultimate strength at failure and the permissible stress generally adopted 3 for concrete based on the cube strength Of crushing and 2 for steel based on the ratio of yield stress to permissible stress , and the modulus of elasticity is a measure of the elastic property of a material and is the ratio between the stress caused by an applied load and the resulting strain or deformation,which disappears on removal of the load in other words it may be represented Modular ratio ie stress in steel / stress in concrete .The modular ratio specified in the Indian code of practice is 2800/3fc where fc is maximum permissible compressive stress due to bending in the concrete in kg /sq cm . According to the code value 1978 said rounded -off value has been given and the Value of M100 grade concrete is 31 ,M 150 is 18.7,M 200 is 13.3 and M 250 is 11 .All this description made is based on IS:456-1978 .
Subscribe to:
Posts (Atom)