Showing posts with label design. Show all posts
Showing posts with label design. Show all posts

DESIGN OF LIQUID RETAINING STRUCTURES IS DIFFERENT FROM THE ORDINARY RCC STRUCTURES

Design of liquid retaining structures is different from the ordinary RCC structures as it requires that concrete should not crack and hence tensile stresses in concrete should be within permissible limits. A reinforced concrete member of liquid retaining structure is designed on the usual principles ignoring tensile resistance of concrete in bending. Additionally, it should be ensured that tensile stress on the liquid retaining face of the equivalent concrete section doesn't exceed the permissible tensile strength of concrete and for calculation purposes the cover is also taken into concrete area. Cracking may be caused due to restraint to shrinkage, expansion and contraction of concrete due to temperature or shrinkage and swelling due to moisture effects. Such restraint may be caused by :--(1) The interaction between reinforcement and concrete during shrinkage due to drying. (2) The boundary conditions (3) The differential conditions prevailing through the large thickness of massive concrete. Use of small size bars placed properly, lead to closer cracks but of smaller width. The risk of cracking due to temperature and shrinkage effects may be minimised by limiting the changes in moisture content and temperature to which the structure as a whole is subjected. The risk of cracking can also be minimized by reducing the restraint on the free expansion of the structure with long walls or slab founded at or below group level, restraint can be minimised by the provision of a sliding layer. This can be provided by founding the structure on a flat layer of concrete with interposition of some material to break the bond and facilitate movement. In case length of structure is large, it should be sub divided into suitable lengths separated by movement joints, specially where sections are changed the movement joints should be provided. Where structures have to store hot liquids, stresses caused by difference in temperature between inside and outside of the reservoir should be taken into account. In water retaining structures a dense unpermeable concrete is required, therefore, proportion of fine and coarse aggregates to cement should be such as to give high quality concrete. Hence concrete mix weaker than M20 is not used. The minimum quantity of cement in concrete mix shall not be less than 300N/cubic metre . Design of liquid retaining structures is different from ordinary RCC structures as it requires that concrete should not crack and hence tensile stresses in concrete should be within permissible limits.

DUE CONSIDERATION SHOULD BE GIVEN TO THE EXISTING TRAFFIC VOLUME, AND PROBABLE GROWTH OF TRAFFIC IN ROAD NET WORK , AS REQUIRED FOR THE POSSIBLE CHANGES IN THE CLASSIFICATION AND IMPROVEMENT OF ROAD NET WORK.

Examination of data for traffic based on the captioned subject of purpose of design &scope, required for the test results of observation pavement deflection measurements the traffic is considered in units of heavy vehicles (Vehicles with a laden weight of 3 tonnes or more) per day, in both the directions in the case of two lane roads and in the direction of heavier traffic in the case of multi lane divided highways. Based on the present traffic volume, the design traffic, i e. the traffic expected at the end of the design year should be estimated. In preparing these estimates due consideration should be given to the existing traffic, possible changes in the road network and land use of the area served, and probable growth of traffic during the period of projection under consideration. It is considered appropriate that major through routes should be designed for at least ten years of life. Less important roads may, however be designed for a somewhat lower period based on growth prospects and the judgement. The traffic count figure used in the formula should normally be seven days average of commercial vehicles derived from 24 hour counts. However in exceptional cases where this information is not available, an average of three day count could also be used for the required analysis for the traffic projection on the main through routes.

RCC FOOTINGS ARE DESIGNED TO TRANSMIT LOAD OF STRUCTURE SUPPORTED BY COLUMNS OR WALLS TO SOIL.

RCC FOOTINGS AND FOUNDATIONS :-- RCC footings are provided to transmit the load of the structure supported by columns or walls to the soil .The design is based on the assumption that the foundation is rigid so that the variation of pressure under the foundation will be linear.The distribution of pressure will be uniform if the centroid of the footing coincides with the resultant of the applied loads .This conventional method holds good only in case of rigid foundation.Such an assumption becomes less and less accurate as the footings becomes relatively more flexible.The requirements in design of foundation are (1) The pressure on the soil should not exceed the bearing capacity of soil (2) The settlement of the structure should be with in the permissible limits .Further there should be no differential settlement. Wherever the possibility of the differential settlement occurs, the different portions of the structure should be made such as to settle independently of each other. The following types of foundation may be used as per the design criterion and design & scope of the bearing capacity and other conditions at the site of work required to be made provided with the RCC footings (1) Continuous footing for walls (2) Isolated footings (3) Combined footings (4) Strap footings (5) Mat or raft foundations (6) Pile foundations.

CLASSIFICATION OF THE FOUNDATIONS AND FACTORS AFFECTING THE SITUATION FOR USE OF THE TYPICAL ARRANGEMENTS ADVISED BY THE IS :1080--1962

DESIGN OF FOUNDATION:--The choice is usually made from experience but it is advisable to carry out a comparative study of the different designs required to determine the most suitable and economical foundation, as the foundations are structural elements that transfer loads from the building or individual column to the earth . If these loads are to be properly transmitted , foundations must be designed to prevent excessive settlement or rotation , to minimise differential settlement and to provide adequate safety against the sliding and overturning effect.Most foundations may be classified as follows :-- (1) Isolated footing under individual column,these may be square , rectangular or circular in plan .(2) Strip foundation and the wall footings.(3) Combined footings supporting two or more column loads .These may be rectangular or trapezoidal in plan or they may be isolated bases joined by a beam .The latter case is referred to as a strap footing.(4) Raft or mat foundation is a large continues foundation supporting all the columns of a structure.This is normally used when soil conditions are poor or differential settlement is to be avoided .(5) In pile foundations pile caps are used to tie a group of piles together .These may support isolated columns, or groups of several columns or load bearing walls .As for as the choice of the type of foundation to be used for the structure in a given situation and position of the structural elements required for transfer of loads it depends on the number of factors for example (a) bearing capacity of the soil (b) type of structure (c) type of loads (d) permissible differential settlement,and (e) economy .

GENERAL NOTES ON THE DESIGN OF THE FOUNDATION (ISI)

The design of RCC footings and foundation is based on the assumption that the foundation is rigid so that the variation of pressure under the foundation will be linear .The distribution or pressure will be uniform if the centroid of the Footing coincides with the resultant of the applied loads .This conventional method holds good only in case of rigid foundation.Such an assumption becomes less and less accurate as the Footing become relatively more flexible.The requirements in design of foundation are (1) The pressure on the soil should not exceed the bearing capacity of the soil .(2) The settlement of the structure should be with in the permissible limits .Further there should be no differential settlement.Whenever the possibility of the differential settlement occures, the different portions of the structure should be made such as to settle independently of each other and where the bearing capacity of soil is low, RCC continues footings are provided and the footings shall be designed to sustain the applied loads, moments and forces and the induced reactions and to ensure that any settlement which may occur shall be as nearly uniform as possible and the safe bearing capacity of soil is not exceeded .In case of the sloped and stepped footings the effective cross section in compression shall be limited by the area above the nuetral plane and the angle of slope and the depth and location of steps shall be such that the design requirements are satisfied at every section sloped and stepped footings that are designed at a unit shall be constructed to assure action as a unit .

REINFORCEMENT REQUIREMENTS FOR DOUBLY REINFOCED BEAMS.

A doubly reinfocement concrete beam is reinforced in both compression and tension regions .The section of the beam may be rectangle,Tor L section .The necessity of using steel in the compression region arises due to two main reasons (1) When depth of beam is restricted ,the strength available from a singly reinforced beam is inadequate.(2) At a support of a continues beam where the bending moment changes the sign ,Such situation may also arise in the design of a beam circular in the plan .TYPES OF THE PROBLEMS :-- There are two types of problems in doubly reinfoced beams just as in the singly reinforced beams (1) Analysis of the section and (2) Design of the section .The analysis of the doubly reinfoced section involves the determination of the amount of resistance knowing breadth ,depth ,area of tension and compression steels and their covers .The analysis is similar to that for the singly reinforced beam except that the compressive force consists of two parts , in steel and in concrete .The stress in compression steel at the collapse limit state may be the yield stress or some what less depending upon the position of the nuetral axis.The stress in compression steel must be compitable  with the strain in the compression steel. When a section or a given dimension is required to carry a given factored bending moment in excess of what it can carry as singly reinforced section ,compression reinforcement becomes necessary.Certain additional tension reinforcement will also be required .However the total tension reinforcement can not exceed the maximum permissible tension reinforcement. The design of a doubly reinforced section involves the determination of cross sectional dimensions and area of tension and compression reinforcements.The first step is to determine whether compression steel is required .This may be done by comparing the factored bending moment with the limiting moment of resistance of a singly reinforced beam.The amount of compression steel may be obtained by writting the equations of the equilibrium.MINIMUM AND MAXIMUM REINFORCEMENT :-- The minimum and maximum amounts of tension reinforcement in a doubly reinforced beam are the same as those in a singly reinforced beam. The minimum compression reinforcement can,of course be zero ,in that case ,it will be a singly reinforced beam .The maximum compression reinforcement can not exceed 4 percent of the gross cross -sectional area of the beam .It is too required to generate the design charts and design tables for the doubly reinforced beams as per the design &scope of the ratio and percentage for different equations of the concrete mix , type of steel and mix of grade .

RCC WELFARE ASSOCIATION REGISTERED NUMBER HPCD 3552 WORKING FOR THE BASIC CONCEPTS AND FOLLOW UP , SENDING SUGGESTIONS TO THE DESIGN & SCOPE AS WELL AS DPR AND EXPEDITING THE REPORTS BASED ON IS AND IRC .

The designers practice required to be attempted in detail and simple treatment of the theory of RCC and design of the RCC Structures,and Complete designs are required to be worked out with detailed analysis and Drawings , giving the basic principles for the use and exercise of Design parameters an ultimate idea of the ultimate load theory as applied to the concrete structures with design charts appended to the work out theory will be found useful to the practical approach of the design work and calculations .The speciality of design work and calculations lies too with the previous comments and suggestions and the analytical approach to the problem of design with certain with basically new conceptions but also in the more comprehensive treatment which makes the design Structures Complete in all respects,even to the extent of minor details.The RTI welfare Association Registered number HPCD 3552 working for the welfare of society and circle as related to the civil construction works it's Design Scope as well as the DPR ,in accordance with the IS Code 456 ,1978 and revised with addition IS 456, 2000 , and expediting the detailed informations to the Resource persons, volunteers and activists on demand under public utilities on the basic concepts of suggestions which have expressed sense of enabling changes and necessary improvement of the civil engineering works .

VARIOUS TYPES OF THE REINFORCED CONCRETE COLUMNS AND IT'S DESIGN FUNDAMENTAL SPECIFIED BY THE IS:456-2000, CODE FOR DETAIL CONSTRUCTION OF THE DESIGN CHARTS .

DESIGN OF COLUMNS:-- The design of walls and Columns is included because the columns and walls behave in a similar manner. A Column may be defined as an element used primarily to support axial compressive loads and with a height of atleast three times it's least lateral dimension. A compression member subjected to pure axially load rarely occurs in practice. All Columns are subjected to some moments which may be due to accidental eccentricity or due to end restraint imposed by monolithically placed beams or slabs. The strength of the column depends upon the strength of the materials , shape and size of the cross -section, length and the degree of positional and directional restraints at its ends .A Column may be classified based on the different criteria such as :- Shape of the cross -section, slenderness ratio ,type of loading and pattern of the lateral reinforcement. A Column may also be classified as short or long Column depending on its effective slenderness ratio
The ratio of effective Column length to least lateral dimensions is referred to as effective slenderness ratio.A short Column has a maximum slenderness ratio of 12 .It's design is based on the strength of the materials and the applied loads .A long Column has a slenderness ratio greater than 12 .However maximum slenderness ratio of a column should not exceed 60 .A long Column is designed to resist the applied loads plus additional BM induced due to its tendency to buckle. On the basis of loading a column may be classified as axially loaded Column, A Column subject to axial load and un-axial bending and a column subjected to axial load and bi-axial bending. A reinforced concrete Column can also be classified according to the manner in which the longitudinal bars are laterally supported ,that is, tied Column and spiral Column.

DISPOSAL OF SEWAGE FROM THE SINGLE HOUSE AND FUNCTION OF THE SEPTIC TANKS .

SEPTIC TANK :-- A septic tank which is a settling tank must be rectangular chamber of RCC or the brick work with cement plastered insides usually built underground .The function of septic tank is to produce certain biological and chemical changes by partial liquefaction and gasification or decomposition of the human excreta discharged into it , through the action of anaerobic bacteria,which flourish in the absence of free oxygen, humidity, darkness and warmth,and which are the conditions created in a septic tank,thus reducing the bulk of the sewage. During the course of action in a septic tank the lighter matter ,grese and fat etc ,rise to the surface and form a thick floating layer called scum while heavier matter sink to the bottom to form sludge .The tanks are made air tight ,water tight and light is also excluded to help decomposition of the sewage.These layers of scum and sewage are not disturbed by the flow of water and the inflow and outflow from the tank are so arranged as to give least disturbance .Both the inlet and the out let pipes are bent downwards and should have their open ends midway in the water .The centre of the outlet pipe is generally kept about 150 mm below the centre of the inlet. A hanging baffle wall making a vertical partition must be arranged which should be 45 cm from the floor and 45 cm away from the inlet pipe however not required in the small tanks .For more design considerations we may follow recommendations given in the IS:2470 .

IRC:81-1981 PROVIDING TENTATIVE GUIDELINES REQUIRED FOR THE STRENGHNING OF FLEXIBLE ROAD PAVEMENTS USING BENKELMAN BEAM DEFLECTION TECHNIQUE .

ANALYSIS OF DATA FOR OVERLAY DESIGN (IRC :81-1981):-- CHARACTERISTIC DEFLECTION :-- Overlay design for a given section is based not on individual deflection values but on a stastical analysis of all the ten measurements in the section corrected for temperature and seasonal variations .This involves calculation of the mean deflection, standard deviation and the characteristic deflection. The characteristics deflection for all design purposes should be taken as the mean deflection plus one standard deviation and used for the recorded proforma based on the analysis of test data prescribed  . TRAFFIC  PROJECTION :-- The purposes of this design method, the traffic is considered in units of heavy vehicles (Vehicles with a laden weight of 3 tonnes or more) per day , in both the directions in the case of two lane roads and in the direction of heavier traffic in the case of multi - lane divided highways .Based on the present traffic, the design traffic ,ie the traffic accepted at the end of the design your should be estimated. In preparing these estimates due consideration should be given to the existing traffic, possible changes in road net work and land use of the area served , and probable growth of traffic during the period of projection under consideration .It is considered appropriate that major through routes should be designed for at least 10 years of life .Less important roads may , however , be designed for a some what lower period based on growth prospects and may be obtained from the formula based on the traffic count figure normally seven days average for commercial vehicles derived from 24 hours counts .However ,in exceptional cases where this information is not available,an average of three days counts could also be used to obtain the result sheet.

IT IS NECESSARY TO FOLLOW CODE OF THE SPECIFICATIONS AND THE STRENGTH OF MATERIALS

Design of the structure is a required necessity of the code and specifications by and virtue of which the DPR is prepared and submitted for the execution of the said structure which is verified under examination of the MOI protected by the strength of materials used in the construction of the structure with value added services failing which it may be failed under the extreme loadings and required strength of material if not maintained at the time of the construction parameters moreover the study of protocol mentioned in the protocol of strength of material is also required to be verified and confirmed before the use whether the material used is with in the specifications .It is also necessary to verify the BC of the soil where the proposed construction is prefixed by the study of protocol realised by the survey conducted and investigation developed for the examination of the layout  plans .As such the design parameters are directly proportional to the values of the strength of material as well as the bearing capacity of the stata traced and research highlighted for the provision made by evaluation under the DPR so the necessary objective of the design parameters should have appropriate look and observation at the level of competent higher authority responsible to protect the safety measures of the book values noticed by the study of protocol mentioned in the code and specifications of the monolithic behaviour of the structure and the material used for required strengthnig of the structure designed with the provision made and created by the DPR highlighted in this behalf of the codal formality accessed through the procedure prescribed for the good strengthnig and future design and scope of the realisation conferred with the procedure prescribed under law code manual of the past performance by the IRC and IS publications

CODE AND SPECIFICATION AND STRENGTH OF STRUCTURE IS NECESSARY REQUIREMENT FOR THE MONOLITHIC CONSTITUTION OF DEFINED CONSTRUCTION

Design of structure is basic necessitated necessity of the code and specification by way and virtue of which inspection of site of work is contoured and planned for physical verification of design data collected from the site of work as per the instructions narrated by IS codes and required by the design engineers responsible for structure s design shape and evaluation calculated on the basis of theoretical assumptions and assessed as per the fundamental of load per unit area required to be  assumed for every component of the structure to be designed and shaped with strength of material  for which classification of soil is required to be tested at the site of work and in the design calculations major considerations are given to strength of soil reported by the Research and laboratory methodologies and if lesser is the strength of soil reported higher would be the values considered for assumptions of the design data expedited for structure on the records Further it is submitted in the matter that a factor of safety is also considered in every type of construction and moments so that it may not failure Obviously it is very clear from the theory of structures that design aspects should not be ignored  by the constructive agencies particularly in hilly areas where geographical  surfacing as well as classification of soil  differs at every step up of the coverage to be structured one with monolithic behavior of the strength of material

Design of structure is basic necessitated necessity of the code and specification

Design of structure is basic necessitated necessity of the code and specification by way and virtue of which inspection of site of work is contoured and planned for physical verification of design data collected from the site of work as per the instructions narrated by IS codes and required by the design engineers responsible for structure s design shape and evaluation calculated on the basis of theoretical assumptions and assessed as per the fundamental of load per unit area required to be  assumed for every component of the structure to be designed and shaped with strength of material  for which classification of soil is required to be tested at the site of work and in the design calculations major considerations are given to strength of soil reported by the Research and laboratory methodologies and if lesser is the strength of soil reported higher would be the values considered for assumptions of the design data expedited for structure on the records Further it is submitted in the matter that a factor of safety is also considered in every type of construction and moments so that it may not failure Obviously it is very clear from the theory of structures that design aspects should not be ignored  by the constructive agencies particularly in hilly areas where geographical  surfacing as well as classification of soil  differs at every step up of the coverage to be structured one with monolithic behavior of the strength of material

Regarding improvement and extra widening to the Ghumarwin Talai Badsar Road

Design  of structure  is essential  and by way and virtue  of which  the road works  are also designed  in the field  of  consideration  design  of sight distance as well as horizontal  and the  vertical  curves failing  which  it would  create  problems  for smooth  driving  of the vehicles  and may help to accident  more over ruling  gradients  are very  necessary  in the hilly ares In accordingly an application  was furnished  with  the  HP  government Shimla department of the  PWD regarding  to consider  the case of improvement  and  widening  to the Ghumarwin Talai Badsar road  and for which  a personal  hearing  was also arranged with  the special  secretary  PWD madam Priyanka Basu and detailed report  as furnished  by office  and authority  further  referred to the Chief Engineer HPPWD Hamirpur  for preparing  of the estimates  and improve  the portions where it is essentially  required In this  connection  further it is submitted  that portion from village  Kathuin to  Daslehra is narow and improvement  of cuves as well as sight distance  and grade revamping  at the  accute narrow escape urgently  required  and for which  an application  along  with reply  of the RTI  issued and respond by the NHAI vide number 11011/21/2015/RTI/PIU-SML/1570 dated 20-09-18 has been furnished   with the endorsement  to Superintending Engineer 10th circle HPPWD Bilaspur  on 07-06-2019 so that pending works of Ghumarwin  division  may be started again  as such the NHAI has refused  the status of NH to this MDR till date of now so necessary  repairs  as well as improvement  of the existing  curves is executed by the PWD authorities and for which  compliance  report if delayed  would  be  the  sole  responsibility  of  the department  as such the above  matter  is also under process  and consideration  with  the  honourable  high court of HP Shimla and will be heard on 25-06-2019 where in queries  raised  are replied  by the NHAI.